About this lab
Three lessons, one valley: first fly from the ground to outer space, then lift a parcel of air, and finally watch an inversion trap a power station's smoke in the valley.
Atmospheric layers
The picture shows an invented valley town and a power station, not any real place. The sky is computed from air density: the higher you go, the thinner the air and the darker the sky. Every number comes from the model: temperature and pressure follow the 1976 U.S. Standard Atmosphere, and the tropical and polar profiles are teaching constructions. The balloon grows with falling pressure and bursts at about 33 km. Plume particles are placed by the model's Gaussian dispersion parameters, their number is proportional to emission, and they are not used to measure concentration or distance.
Three results
Three results
- Layers: in the troposphere temperature falls 6.5 K per km on average up to the tropopause at about 11 km; the upper stratosphere warms because ozone absorbs ultraviolet, returning to about −2.5 °C near 49 km; the mesosphere cools again, to about −86 °C near 86 km; the thermosphere warms once more. Layer boundaries change with latitude and season; this lab uses 16.5 km (tropical), 11 km (mid-latitude) and 8.5 km (polar) as teaching values. Pressure falls with height in every layer, and warming in the stratosphere does not change that.
- Stability: a rising parcel cools at the dry adiabatic rate, taken as 10 K/km here, and is compared with its surroundings. A parcel colder than the environment is pushed back; a warmer one keeps rising. When the environmental lapse rate is smaller than the parcel's cooling rate the air is stable, so in sounding A (6 K/km) air that cools with height is still stable, and only sounding C (12 K/km) is unstable. A saturated parcel follows the moist adiabat, about 4.2 K/km at 20 °C, so in sounding A a saturated parcel shoots upward.
- Inversion: in sounding B temperature rises through the lowest 0–0.5 km. Lift a parcel 0.5 km: it is 5 °C against 14 °C outside, a difference of −9 °C; in sounding A the difference is −2 °C. A stable layer squeezes the mixed layer thin: with the same 5 K of surface heating, sounding A mixes to about 1250 m and sounding B only to about 260 m. In the box model concentration = background + emission ÷ (wind speed × valley width × mixing height). With zero emission only the background remains; double the wind and the increase halves; a chimney taller than the lid puts the plume above it. An inversion suppresses upward mixing, but concentration also depends on emission and horizontal ventilation.
Model and sources
Model and sources
- The standard atmosphere is the 1976 U.S. Standard Atmosphere: layer formulas from 0 to 86 km (geopotential heights 0, 11, 20, 32, 47, 51, 71 and 84.852 km; lapse rates −6.5, 0, +1, +2.8, 0, −2.8 and −2 K/km) and a table above 86 km. Heights on the page are geometric, so the boundaries are slightly higher than the geopotential values, e.g. 11 km becomes 11.02 km. The tropical profile (300 K at the surface, tropopause at 16.5 km) and the polar one (270 K, 8.5 km) are teaching constructions, not measured soundings; sources differ on tropical and polar tropopause heights, so round values within their range are used. Cumulative mass is 1 − p ÷ p₀, ignoring the slight decrease of gravity with height.
- The sky is shaded by single-scattering integration, with Rayleigh and Mie scattering and ozone absorption coefficients from Hillaire 2020 and air density taken from the model. The ozone band at 15–35 km is schematic; about 90% of ozone is in the stratosphere. High ozone concentrations near the ground are a pollutant, which this lab does not model.
- The parcel does not mix with its surroundings. A saturated parcel is saturated from the ground up and follows the moist adiabat; saturation vapour pressure uses the Magnus formula; condensate fallout and freezing are ignored. After release the buoyant acceleration is integrated once per second, and the parcel stops when it returns to the ground.
- Mixing height uses Holzworth's method: a surface parcel, heated, rises along the dry adiabat and the lid is where it meets the environmental profile. The 100 m lower limit is a teaching value. Stability class follows Pasquill: by wind speed in the day, and by wind speed and the near-surface temperature gradient at night. The plume is Gaussian, with dispersion parameters from a fit to the Pasquill–Gifford curves and multiple reflections from the ground and the lid; plume rise and valley circulation are ignored. The valley is 10 km long and 6 km wide with a 10 µg/m³ background; emissions are teaching values, not predictions for any power station or city.
- U.S. Standard Atmosphere 1976 · layer table and constants ↗ checked 2026-11-16
- PDAS · 1976 standard atmosphere tables (0–1000 km) ↗ layer formulas checked point by point; nodes above 86 km taken from this table, checked 2026-11-16
- Engineering ToolBox · standard atmosphere table ↗ independent reference, checked 2026-11-16
- NASA Glenn · Earth Atmosphere Model ↗ independent reference for the three-piece fit, checked 2026-11-16
- NOAA JetStream · layers of the atmosphere ↗ layer boundaries and tropopause height by latitude, checked 2026-11-16
- Tropopause · WMO definition and heights ↗ checked 2026-11-16
- NOAA Ozone Assessment 2018 · Twenty Questions, Q1 ↗ about 90% in the stratosphere, 15–35 km, checked 2026-11-16
- Hillaire 2020 · A Scalable and Production Ready Sky and Atmosphere Rendering Technique ↗ scattering and absorption coefficients, checked 2026-11-16
- Vapour pressure of water · Magnus formula and saturation vapour pressure table ↗ checked 2026-11-16
- Lapse rate · dry and moist adiabatic rates and stability ↗ checked 2026-11-16
- EPA-454/R-99-005 · Pasquill stability tables 6-3 and 6-7 ↗ checked 2026-11-16
- EPA · MIXHTSD mixing height (Holzworth's method) ↗ checked 2026-11-16
- Atmospheric dispersion modeling · dispersion parameters and the Gaussian plume ↗ checked 2026-11-16