OPOpenPithMake curiosity visibleGeography lab / Orographic rain and foehn

About this lab

Three topics, one model: push a parcel of air over a mountain, work out where the cloud base is, then compare three mountains.

A mountain blocks the wind and forces the air upward. The air expands and cools as it rises. When it cools to the dew point the vapour condenses into cloud, and the latent heat released slows the cooling. The water falls as rain on the windward slope, and the air that crosses the ridge sinks and warms, so the foot of the lee slope ends warmer and drier than where it started. That is a foehn. A mountain in the wind does not guarantee rain: the air needs enough vapour and the mountain must be higher than the condensation level.

The picture is an original teaching model, not any real place: a 2000 m ridge, 80 km from east to west, stretched 8 times vertically, with schematic rock layers. The parcel is drawn enlarged: its volume change is exaggerated 3 times, and the readout gives the true value. The cloud is volume-rendered and its base is a strictly horizontal plane at the condensation level the model computes. All numbers come from the model. The 28 °C is what the model gives under its stated assumptions, not a forecast for any valley.

Three results

Three results

  • Condensation level: every 100 m of lift closes the gap between temperature and dew point by 0.8 °C, so the condensation level = 125 × (temperature − dew point) m. At 25 °C with a 15 °C dew point it is 1250 m and the cloud-base temperature is 12.5 °C. With a 5 °C dew point it is 2500 m, above a 2000 m summit, and there is no cloud at all.
  • Two lapse rates: an unsaturated parcel cools 1.0 °C per 100 m of lift and its dew point falls 0.2 °C; once saturated it cools only 0.6 °C per 100 m because condensation releases latent heat. In the reference case the summit is 8.0 °C, the pressure 795 hPa, and the parcel is about 20% larger than at the foot. These are fixed values chosen so the work can be done by hand.
  • Foehn: the condensed water falls out on the windward side, and the sinking parcel is no longer saturated, so it warms 1.0 °C per 100 m, 0.4 °C more per 100 m than it cooled inside the cloud. Lee foot temperature = foot temperature + 0.4 × rainout × (height − condensation level) ÷ 100. The reference case gives 28.0 °C and a 3000 m mountain gives 32.0 °C. A 1000 m mountain or a 5 °C dew point returns to 25.0 °C. Relative humidity falls from 54% to 37%: the lee side is both warmer and drier.

Model and sources

Model and sources

  • The mountain is a smooth single peak, h(x) = H × exp(−(x ÷ 12 km)²). The parcel hugs the slope at 10 m/s for 80 km, about 2.2 h; one horizontal unit in the picture is 1 km. Real flow around the mountain, blocking, lee waves and inversions are not simulated.
  • Saturation vapour pressure uses the Magnus formula 6.1094 × exp(17.625 T ÷ (T + 243.04)) hPa, pressure uses the standard atmosphere, and the mixing ratio is w = 622 e ÷ (p − e). The given rule that the dew point falls 0.2 °C per 100 m only approximately conserves vapour: 10.63 g/kg at the foot and 10.50 g/kg at the cloud base. The water budget uses the foot value and the saturated summit value.
  • The lee cloud base z_b = condensation level + rainout × (height − condensation level) is a teaching rule: cloud water grows linearly with height above the cloud base. Solving the water budget strictly gives a lee cloud base about 40 m different at 50% rainout.
  • The cloud shadow, rain and flow lines are schematic: rain density is proportional to the rainout fraction and no millimetres are given; the flow lines only show where the wind comes from.
Back to geography ↑